Auto Mate AM6.2 Installationsanleitung

Model AM6.2Installation Guide© 2007 Directed Electronics, Vista, CA N4101A 2007-06

10 © 2007 Directed Electronics—all rights reservedprimary harness (H1) wiring diagram______________________________________________________4-pin satel

© 2007 Directed Electronics—all rights reserved 11heavy gauge relay wiring diagram____________________________________door lock harness, 3-pin connect

12 © 2007 Directed Electronics—all rights reservedprimary harness (H1), 9-pin connectorThis wire sends a negative pulse every time the remote start is

© 2007 Directed Electronics—all rights reserved 13NOTE: When the activation pulse count can be programmed to 1, 2, or 3 pulses when changed it willaff

14 © 2007 Directed Electronics—all rights reservedThis input comes from the factory set to 1 activation pulse. This means that it is necessary to have

© 2007 Directed Electronics—all rights reserved 15IMPORTANT: Do NOT connect this wire to a negative vehicle light flash wire before changing theprogra

16 © 2007 Directed Electronics—all rights reserved4-Pin Satellite HarnessWhen the remote start goes active this wire supplies a (-) 200mA output. It c

© 2007 Directed Electronics—all rights reserved 17heavy gauge relay interfaceThe heavy gauge wires are used to energize high current circuits in the v

18 © 2007 Directed Electronics—all rights reservedremote start harness (H2), 5-pin connectorConnect this wire to the toggle (override) switch as shown

© 2007 Directed Electronics—all rights reserved 19This wire MUST be connected to the hood pinswitch. This input will disable or shut down the remote s

2 © 2007 Directed Electronics—all rights reservedtable of contentsCode Hopping™, Doubleguard®, ESP™, FailSafe®, Ghost Switch™, Learn Routine™, Nite-Li

20 © 2007 Directed Electronics—all rights reservedthe unit prematurely.You must also connect the H2/4 BROWN (+) shut-down input to the yellow wire on

© 2007 Directed Electronics—all rights reserved 21pre-1996 dodge dakota pickups with 2.5 liter motorsgeneral motors trucks, SUVs, and column shifting

22 © 2007 Directed Electronics—all rights reservedbypassing GM vehicle anti-theft systems (VATS)Vehicles with the GM VATS (Pass Key) systems have a re

© 2007 Directed Electronics—all rights reserved 231995 and newer vehicle anti-theft systems(immobilizers)1995 and newer vehicle anti-theft systems (im

24 © 2007 Directed Electronics—all rights reservedwill excite the transponder, which is located (but not visible) in the head of the ignition key. The

© 2005 Directed Electronics—all rights reserved 25programming jumpersThis jumper is used to determine the light flash output polarity. In the (+) posi

26© 2003 Directed Electronics, Inc. Vista, CAplug-in program switchThe Program switch plugs into the blue two-pin connector. transmitter/receiver lear

© 2007 Directed Electronics—all rights reserved 27auto learn transmitter configurationbutton one Car LocatorRemoteStart/Unlock during start Remote Sta

28 © 2007 Directed Electronics—all rights reservedtach learning1. Start the vehicle with the key.2. Within 5 seconds, press and HOLD the Program switc

© 2007 Directed Electronics—all rights reserved 293. Transmit. The transmitter is used to select the desired setting. As shipped,the default fea-tures

© 2007 Directed Electronics—all rights reserved 3what is included The control module (see diagram) Two remote transmitters The plug-in program swit

30 © 2007 Directed Electronics—all rights reservedfeatures menuThe factory default settings are indicated in bold text in the table below.FEATURE LED

© 2007 Directed Electronics—all rights reserved 31feature descriptionsThe features of the system are described below.1 ENGINE CHECK—ON/OFF: In the def

32 © 2007 Directed Electronics—all rights reserved8 ACTIVATION PULSE COUNT—1/2/3 PULSES: This feature allows the number of pulses to activate the remo

© 2007 Directed Electronics—all rights reserved 3318 IGNITION CONTROLLED LOCK—ON, OFF: When programmed ON the doors will lock when the key is turned t

34 © 2007 Directed Electronics—all rights reservedThe LED will stop flashing when the ignition is turned on.safety checkBefore vehicle reassembly, the

© 2007 Directed Electronics—all rights reserved 35down the remote start system.f. Activate the remote start system. If the starter engages, immediate

36 © 2007 Directed Electronics—all rights reserved The climate control system does not work while the unit is operating the vehicle.Either the wrong

© 2007 Directed Electronics—all rights reserved 37 The vehicle will start and run only for about 10 seconds.1. Is the remote start programmed for vol

38 © 2007 Directed Electronics—all rights reservedwiring quick reference guideNo Function

4 © 2007 Directed Electronics—all rights reservedwarning! safety firstThe following safety warnings must be observed at all times: Due to the complex

© 2007 Directed Electronics—all rights reserved 5installation points to rememberIMPORTANT! This product is designed for fuel-injected, automatic tran

6 © 2007 Directed Electronics—all rights reservedfinding the wires you needIMPORTANT! Do not use a 12V test light or logic probe (computer safe test l

© 2007 Directed Electronics—all rights reserved 75. Cut the wire you suspect of being the starter wire. 6. Attempt to start the car. If the starter en

8 © 2007 Directed Electronics—all rights reservedMost vehicles use a (+) parking light circuit. The (+) parking light wire is often found near the lig

© 2007 Directed Electronics—all rights reserved 9can use a fuel injector control wire for engine speed sensing. Common locations for a tachometer wire